@javierarch.bsky.social
Pro tip to anyone working on unit layouts ( arch) : block in the minimum required spaces before drafting. Don't waste time finishing a layout to only realize it does not work because the unit bathroom cannot fit or the bedroom is too small. Bathrooms, doors, min. clearances 1st.
November 14, 2025 at 2:39 PM
Pro tip to anyone working on unit layouts ( arch) : block in the minimum required spaces before drafting. Don't waste time finishing a layout to only realize it does not work because the unit bathroom cannot fit or the bedroom is too small. Bathrooms, doors, min. clearances 1st.
Recently changed to a hardened steel nozzle, is my issue just my filament is too wet? This is with PETG. I tried drying but maybe not long enough/ hot enough. Using Kobra S1
November 14, 2025 at 5:17 AM
Recently changed to a hardened steel nozzle, is my issue just my filament is too wet? This is with PETG. I tried drying but maybe not long enough/ hot enough. Using Kobra S1
First Frosty night of the year for me, I brought all my plants inside! Not something I considered when growing my plant collection! 😅
November 10, 2025 at 11:17 PM
First Frosty night of the year for me, I brought all my plants inside! Not something I considered when growing my plant collection! 😅
Finally got my official anycubic hardened steel nozzle, took almost 2 months to ship! The installation was a lot easier than I thought, if not almost painless. Still concerned the nozzle will scratch the bed, can only wait to see how the full calibration goes 🤞. Dreading changing the extruder...
November 8, 2025 at 7:02 PM
Finally got my official anycubic hardened steel nozzle, took almost 2 months to ship! The installation was a lot easier than I thought, if not almost painless. Still concerned the nozzle will scratch the bed, can only wait to see how the full calibration goes 🤞. Dreading changing the extruder...
Some tiny leaves sprouted at the base of my Hoya shepherdii, #hoyas Can someone tell if these are sprouts of my Hoya or just weeds? #indoorplants
November 5, 2025 at 9:47 PM
Some tiny leaves sprouted at the base of my Hoya shepherdii, #hoyas Can someone tell if these are sprouts of my Hoya or just weeds? #indoorplants
Never seen a "sweet notice" before...wonder what that is a mistranslation of🤔
October 30, 2025 at 10:34 PM
Never seen a "sweet notice" before...wonder what that is a mistranslation of🤔
Pro #revit tip: if you are working on a model that is going or has gone through many back and forth changes - keep a model log. Know which version is what, mention any models reverted, file locations. Its painful to get back to a project years later only to find a mess w/o any notes.
October 30, 2025 at 2:38 PM
Pro #revit tip: if you are working on a model that is going or has gone through many back and forth changes - keep a model log. Know which version is what, mention any models reverted, file locations. Its painful to get back to a project years later only to find a mess w/o any notes.
Revit is down, due to AWS, Autodesk needs to change their status to outage, 150 products down is not a disruption. Time to do some offline tasks...
Health.autodesk.com
Health.autodesk.com
Autodesk Health Dashboard Status
Welcome to Autodesk Health Dashboard's home for real-time and historical data on system performance.
Health.autodesk.com
October 20, 2025 at 2:09 PM
Revit is down, due to AWS, Autodesk needs to change their status to outage, 150 products down is not a disruption. Time to do some offline tasks...
Health.autodesk.com
Health.autodesk.com
Autodesk health check site is down, and the ACC is throwing XML errors, not looking like a good day. Sync your models frequently #revit
September 8, 2025 at 3:34 PM
Autodesk health check site is down, and the ACC is throwing XML errors, not looking like a good day. Sync your models frequently #revit
Just got my first burn with. My 3d printer, I am officially initiated into the community.
On a side note what a pain in the ass it was to clear a clog in the extruder in the Kobra S1! That has totally turned me off the S1. I still like it, but brutal maintenance. Wonder if it's always like that...
On a side note what a pain in the ass it was to clear a clog in the extruder in the Kobra S1! That has totally turned me off the S1. I still like it, but brutal maintenance. Wonder if it's always like that...
August 16, 2025 at 4:56 AM
Just got my first burn with. My 3d printer, I am officially initiated into the community.
On a side note what a pain in the ass it was to clear a clog in the extruder in the Kobra S1! That has totally turned me off the S1. I still like it, but brutal maintenance. Wonder if it's always like that...
On a side note what a pain in the ass it was to clear a clog in the extruder in the Kobra S1! That has totally turned me off the S1. I still like it, but brutal maintenance. Wonder if it's always like that...
Just installed Revit 2026 and was getting awful performance. Looks like hardware acceleration being on in the settings by default was the culprit, but now I can't use the new "accelerated graphics" feature...might be time to upgrade my PC 😞
May 31, 2025 at 7:18 PM
Just installed Revit 2026 and was getting awful performance. Looks like hardware acceleration being on in the settings by default was the culprit, but now I can't use the new "accelerated graphics" feature...might be time to upgrade my PC 😞