abstract fusion
LightNews LightNews
abstractfusion.bsky.social
abstract fusion
@abstractfusion.bsky.social
5 followers 3 following 18 posts
fusion360 abstractions and doohickeys
documenting my CAD relearning experience
alt account of a certain raven. she/it
Posts Replies Media Videos
abstractfusion.bsky.social
object 11
A hexagonal drill bit created with the sweep twist tool. #fusion360 A hexagonal drill bit created with the sweep twist tool. #fusion360
September 30, 2025 at 12:57 PM
abstractfusion.bsky.social
object 07.5, i should've included these fillets from the start ngl
Object 07 as shown in the previous post, but the interior top face is now filleted. This should have been obvious at the time but I never did it. Object 07's exterior top face is also filleted.
September 29, 2025 at 1:12 PM
abstractfusion.bsky.social
object 10
A hexagonal component which arcs upward and out to the left, then out to the right again - bottom flat with the working plane, top roughly perpendicular. #3dart #fusion360 View from opposite side of same object. The interior of the curve is a little scuffed due to the shape of the spline used for the sweep profile.
September 29, 2025 at 1:09 PM
abstractfusion.bsky.social
object 09
A sketch-layer cutaway of half of a pawn with lots of labelled dimensions - arcs, tangents, and radii shoot off into nothing, or meet and are constrained at the left wall. #fusion360 The same pawn, revolve extruded out into a full object. It is rounded, smooth and shiny, with a flared base and another flare near the top below the ball. #3dart
September 22, 2025 at 5:56 PM
abstractfusion.bsky.social
object 08
An object made from a triangular prism. The front side is flat, with no curves or extrusions, save for a triangular incursion at the bottom, giving the whole front a chevron-like appearance. #3dart #fusion360 The same object, viewed from below. It is seen that the incursion at the bottom extends quite far, hollowing out the inside. The upper rear of the object is curved from the point of the triangle to meet the flat chevron front. #3dart #fusion360 The object, viewed head on. It has a distinct chevron appearance. The incursion would be invisible if not for the shadow. #3dart #fusion360
September 18, 2025 at 12:52 PM
abstractfusion.bsky.social
object 07
A squat square object with blunt rounded corners. In the center, a hollow ring is raised from the top of the object, with smooth tapered surfaces leading up to the ring. #3dart #fusion360 The same object, viewed from below - it is hollow, with exceptionally thin walls. The raised ring from before extends down as a shaft through the inside of the object. #3dart #fusion360
September 18, 2025 at 12:49 PM
abstractfusion.bsky.social
object 06
An object with a long hollow shaft on one side, adjoined to a short open ring by a roughly trapezoidal bridge. #3dart #fusion360 #3d #art
September 15, 2025 at 1:05 PM
abstractfusion.bsky.social
object 05
A horizontal cylinder with domed edges, supported by two rectangular girders wrapping around in a ring. A single pipe moves down from one edge to the ground and runs offscreen. #3d #art #3dart #fusion360 A horizontal cylinder with domed edges, supported by two rectangular girders wrapping around in a ring. A single pipe moves down from one edge to the ground and runs offscreen. #3d #art #3dart #fusion360 A horizontal cylinder with domed edges, supported by two rectangular girders wrapping around in a ring. A single pipe moves down from one edge to the ground and runs offscreen. #3d #art #3dart #fusion360 A horizontal cylinder with domed edges, supported by two rectangular girders wrapping around in a ring. A single pipe moves down from one edge to the ground and runs offscreen. #3d #art #3dart #fusion360
September 9, 2025 at 1:40 PM
abstractfusion.bsky.social
object 04
A square ogee-edged pedestal supports a rather short, squat rectangular beam, itself holding up a sphere with a diameter equal to the pedestal. The base of the sphere holds a short pipe shooting off to the right, holding up another, smaller sphere balanced slightly above the center of the pipe. Another pipe juts out from the pedestal and runs up the beam into the first sphere, outputting in the ground. #art #3d #fusion360 A square ogee-edged pedestal supports a rather short, squat rectangular beam, itself holding up a sphere with a diameter equal to the pedestal. The base of the sphere holds a short pipe shooting off to the right, holding up another, smaller sphere balanced slightly above the center of the pipe. Another pipe juts out from the pedestal and runs up the beam into the first sphere, outputting in the ground. #art #3d #fusion360
September 5, 2025 at 1:21 PM
abstractfusion.bsky.social
object 03
A rectangular truss with two support boards intersecting at an X. #art #3d #fusion360
September 4, 2025 at 3:39 PM
abstractfusion.bsky.social
object 02
Corner-front view. A rounded cube with a cubic eighth missing. The missing section is cushioned and bordered with six thick pipe segments in a roughly hexagonal shape. The cube has a pipe sticking out of the opposite corner as the missing section. #art #fusion360 #3d Side view. A rounded cube with a cubic eighth missing. The missing section is cushioned and bordered with six thick pipe segments in a roughly hexagonal shape. The cube has a pipe sticking out of the opposite corner as the missing section. #art #fusion360 #3d Underside view. A rounded cube with a cubic eighth missing. The missing section is cushioned and bordered with six thick pipe segments in a roughly hexagonal shape. The bottom of the cube has a spherical indentation. #art #fusion360 #3d
September 4, 2025 at 1:55 PM
abstractfusion.bsky.social
object 01
a rectangular brick-like object, with a cone-shaped indentation and smoothed edges leading down to the divot #fusion360 #art #3d a rectangular brick-like object, with a cone-shaped indentation and smoothed edges leading down to the divot #fusion360 #art #3d
September 4, 2025 at 1:48 PM