LightNews LightNews
myhandsarecats.bsky.social
@myhandsarecats.bsky.social
130 followers 520 following 44 posts
Posts Replies Media Videos
Reposted
nittles.bsky.social
Repost if you think Ike is awesome! Or you want to see the life force drain out of the US Supreme Court
June 19, 2025 at 4:08 PM
myhandsarecats.bsky.social
Engine is out!
I wanted to do this in a day, but ran into some complications with the crane that set me back.
An engine crane, left, suspending an engine in front of a car's engine bay, right.
April 28, 2025 at 11:53 AM
myhandsarecats.bsky.social
Wrapping up the inside of my Brat, thought a little before and after would be nice
April 23, 2025 at 12:35 PM
myhandsarecats.bsky.social
Here's what it sounds like
March 5, 2025 at 6:00 PM
myhandsarecats.bsky.social
The new motorcycle exhaust still sounded a bit like two weed wackers running at the same time, so I made a quick mod
The inside of a motorcycle exhaust, showing the silencer plug that the manufacturer welded in. It's a cylinder with a bunch of little holes, which forces the exhaust noise to slow down and become more muffled as it exits. In the background is a blind rivet gun, which is used to permanently attach two pieces of metal by clamping them together through a hole. The same muffler tip, this time with the holed-cylinder removed. Now exhaust pulses can travel more freely, though are still required to go through a baffled piece of metal. The cup shape on the inside of the muffler causes turbulence as the gasses exit, quieting the noise slightly. Also, the muffler itself (not pictured) is packed with insulating material and is designed to attenuate sound, so it won't be thunderously loud.
March 5, 2025 at 4:36 PM
myhandsarecats.bsky.social
Big fixes! Chopped up some neoprene to fill in the gaps, then covered that with more Bondo. It wasn't perfect, but after a little sanding and painting, it looks much better than before.
A picture of a dashboard, showing how chunks of neoprene foam were added to a cavity. A hot glue gun is on the right, demonstrating that the chunks were held down in the cavity. The same dash, now with the cavities filled with dark teal Bondo - a two part hardening body filler, reinforced by short hair glass fiber. The same dash, now with a pre-cut fabric dash cover. The roughest spots of Bondo are not visible, but the two cracks that were very obvious are now much less so.
March 2, 2025 at 6:41 PM
myhandsarecats.bsky.social
Rollercoaster of a weekend working on the car. Check the alt text, but the long story short is I need more Bondo
Had an idea last week to use foam filler to repair the cracks on my dash. I spent about three hours prepping, because I needed to put tape in a very tight area, and that ended up cutting my hand up. I feel at this point that the foam was working well though, it was very firmly stuck in place and I had started shaving it down to the right shape - no more cracks on the dash. Then I added Bondo, but had to throw away a bunch of it because it had started crystalizing in the can. I shouldn't have left it on the shelf for a year I think. Filled in the little gaps of foam, finalized the shape of the dash, and it's looking ready for *glazing putty*. I didn't realize though, that the putty was going to start dissolving the foam I was so happy with. So now we're here, with the red glazing putty on top of the blue body filler. I had no reason to suspect that it would eat the foam, but now there are three huge divots where there used to be foam. Luckily it stopped before it ate all the way through, and now I have a platform to add more body filler on top of.
February 24, 2025 at 1:16 AM
myhandsarecats.bsky.social
@foxwithtacos.bsky.social: "hey, can you make a front camera cover for my phone"

Why yes, and I already have the perfect idea
The camera cover I designed, which is in the shape of a trucker hat with the text "Foxy Grandpa" on it. Guest starring my daruma.
February 19, 2025 at 11:57 PM
myhandsarecats.bsky.social
It turns out just deciding to go for it was what I needed. There were a few months of what felt like zero progress, but here we are with a clean cabin, some filled holes, and a refreshed wiring harness.
The interior of a Subaru Brat, seen from the perspective of the passenger side. I've added carpet - a loop pile shag, in a color called Saddle. It stops halfway from the back, so the part where people's feet go is still bare. I want to verify the front isn't leaking before adding the carpet there. There are a few interior plastics added back in, but no seats yet. The inside of a Subaru Brat, at an earlier stage. The dash has been put in, but it isn't fully mounted, causing it to hang forward slightly. Since taking it out, I've cleaned all the AC vents, rebuilt the wiring harness, and blocked rust holes. There are still cracks on the top, the result of sun damage.
February 17, 2025 at 10:22 PM
myhandsarecats.bsky.social
Maybe what I really need is to just drive the dang car
February 12, 2025 at 1:06 PM
myhandsarecats.bsky.social
Alright, so. There's so many problems I won't be able to fix on this car that I don't feel like it's worth the effort to polish the stuff I can. I decided that I'm just going to clean up what I can and put it all back together. Maybe someone else will be able to take it all the way to the finish.
February 10, 2025 at 12:40 AM
myhandsarecats.bsky.social
Back at it on the project car... Again finding more rust.
A look inside the fresh air ventilation duct under the windshield of a car. This is where fresh air gets sucked in, then cooled by the HVAC system. Along the seam where the duct was welded to the firewall, so much rust is apparent that you can see through into the driver's foot well. The rust has currently been cleaned, and is undergoing etching before it will be painted with a rust-killing paint.
February 4, 2025 at 10:20 PM
myhandsarecats.bsky.social
Just another day of working on an old car. This is the wiper motor, I took it off to have better access to paint under it. While I have it off, I decided to pack more grease and I somehow ended up with the housing off. Cleaned up the whole thing, now I'm not sure if I have it back together right
A brushed DC motor, used to rotate windshield wipers. It's a mass of copper and magnets, a circuit board on the bottom, and three graphite "brushes" on the bottom. These brushes contact the electromagnet in the rotating mass, completing the circuit, and allow the mass to rotate. They are contained within three gold colored housings, and each have a small spring to keep the contact snug. DC motor brushes do wear out over time, but this motor in particular does not rotate enough to warrant replacing, even after 40 years of service. The part where I think I don't have together correctly is not pictured, but it has to do with the clocking of the plastic gear.
January 25, 2025 at 7:52 PM
myhandsarecats.bsky.social
Today's work: Finish sanding the bondo in the engine bay, clean it up, then paint it with POR-15. Sand, clean, etch, paint on the seam behind it. Clean up leftover adhesive on the passenger side port hole, then wrap it and plug it.
The firewall of an old car, seen above from the engine bay. This is where the Subaru Brat holds a spare tire, and the platform itself is spot welded in a few places to the firewall. This configuration allows water to flow underneath the platform, where it gets sandwiched between two plates of metal - eventually causing the lower portion to rust completely away. Around the seam that formerly allowed water to seep in, pale blue body filler has been added to potentially keep water out.
January 24, 2025 at 4:30 PM
myhandsarecats.bsky.social
The old subaru has more than a few rust holes, but I think I can manage them. I sealed up where the holes in the engine bay were, so I don't think it'll get worse.
The interior of an old car, stripped down to the metal. There are spots where rust has eaten away - these came from areas where water was allowed to pool due to the design of the car. The engine bay has a spot where the spare tire sits, which became a shelf that does not allow water to evaporate quickly.
January 24, 2025 at 3:53 PM
myhandsarecats.bsky.social
I wanted to find a way to reuse my 3d print purge waste rather than just throwing it all out. Here's a test die to find out how to resin.
A single 20 sided die, black in color with glitter embedded. There is flashing from the mold on an edge, and several voids are present where air bubbles stuck to the mold. The side numbered 20 is face up.
January 6, 2025 at 8:41 PM
myhandsarecats.bsky.social
Bluesky is becoming one of my favorite social media sites because it lets people share block/moderation lists. Check out the steps to add a block list to your feed here:
In the search bar, type "@skywatch.blue". Select the result account, Anti-Alf Aktion In the account's Lists tab, browse the selection of various moderation lists. Click one that you want to block. When the page opens, verify the description matches what you want to block. Press the subscribe button, and then press "Block accounts".
November 8, 2024 at 2:58 PM
myhandsarecats.bsky.social
I grew up in these streets
A view of Delfino Plaza, from 2002's Super Mario Sunshine. Mario is in the foreground, facing away and looking down at the plaza from the top of a belltower.
November 6, 2024 at 3:18 AM
myhandsarecats.bsky.social
This wiring stuff can be not so fun
POV shot of the interior of a car, the interior ripped out and wires laying everywhere. On my lap is the Hayne's manual for the car, place held by a flashlight. The book is open to the wiring diagrams of the car.
November 4, 2024 at 9:37 PM
myhandsarecats.bsky.social
Drove about 5 hours to get better doors
October 31, 2024 at 3:51 PM
myhandsarecats.bsky.social
Idk what it is about threads, but I seem to only be getting people vagueposting
October 26, 2024 at 7:12 PM
myhandsarecats.bsky.social
I've made 74 applications since keeping track, not a single reply 👍👍👍👍👍👍
The actual number is probably double that, I've been doing this since July
October 24, 2024 at 4:53 PM
myhandsarecats.bsky.social
Plan for the Brat:
- strip interior
- evacuate AC refrigerant
- Bring to body shop for rust and paint
- rebuild engine
- rewire
- think about EJ/suspension swap later
October 24, 2024 at 1:35 PM
myhandsarecats.bsky.social
Pulled the AC evaporator housing. I'm thinking squirrels got in here somehow
October 24, 2024 at 1:33 PM
myhandsarecats.bsky.social
Oh boy. This is going to be fun to put back together
The interior of my Subaru brat, most panels have been removed, and the dashboard is off, revealing the HVAC vents.
October 22, 2024 at 3:18 PM