𝑱𝒆𝒔𝒖𝒔 𝑩𝒖𝒓𝒏𝒔 𝑵𝒆𝒐𝒏
LightNews LightNews
banner
jesusburnsneon.bsky.social
𝑱𝒆𝒔𝒖𝒔 𝑩𝒖𝒓𝒏𝒔 𝑵𝒆𝒐𝒏
@jesusburnsneon.bsky.social
23 followers 37 following 26 posts
Traded poetry for an orchestra of retro console mods and cosplays 👾 Fluent in EFT, Reiki, and gongs 🔔 Yes, I’m THAT free hugs guy at the con. BSJ

https://lnk.bio/jesusburnsneon
Posts Replies Media Videos
jesusburnsneon.bsky.social
Thank you! I added the mount as a maintenance access approach to minimize the Q teardown into just taking off the side panel on the occasion a microSD swap is ever required. Although I guess you could cut an opening in the side panel above the fan grates for quicker access. Doodled a cutout example:
Example of a cutout region as another method to access the microSD from the AIO Fan Bracket
November 6, 2025 at 10:19 PM
jesusburnsneon.bsky.social
Along the way, I created companion 3D models including a Panasonic Q AIO fan bracket remix from @collingall.bsky.social's GC Fan Mod to mount FlippyDrive (@trevor.rudol.ph & @chrispville.bsky.social) and a microSD adapter (@humblebazooka.com). Check 'em out!
makerworld.com/en/@jesusbur...
Panasonic Q Retro GEM WiFi Antenna Mount (top) Panasonic Q Retro GEM HDMI Mount (bottom) Panasonic QAIO Fan Bracket with FlippyDrive, microSD adapter, and GEM Antenna mounts Panasonic Q reassembled Retro GEM HDMI via Panasonic Q's backplate
November 6, 2025 at 7:57 PM
jesusburnsneon.bsky.social
Here's a short clip showing the Panasonic Q's video output between S-Video and HDMI (Retro GEM) via Morph 4K.
November 6, 2025 at 7:57 PM
jesusburnsneon.bsky.social
I installed a @pixelfx.co Retro GEM in a Panasonic Q! #GameCube #Nintendo
Retro GEM installed on the Panasonic Q's GameCube pcb Panasonic Q Retro GEM HDMI Mount
November 6, 2025 at 7:57 PM
jesusburnsneon.bsky.social
Photos I snapped during my @pixelfx.co 3DO GEM install.

#PixelFX #Panasonic3DO #RetroGEM
Tacking down the 3DO GEM flex before touching up pins and final cleanup 3v3 Power Board Running ffc from GEM to rear port Drilled port for mini HDMI
July 1, 2025 at 12:30 AM
jesusburnsneon.bsky.social
🍌
November 25, 2024 at 9:40 PM
jesusburnsneon.bsky.social
This print turned out very well. Took hella long, but it was worth the wait. Think I’m starting to get the hang of printing with Inland PLAs. Their purple tough PLA is 🤌🏻, and I’m amazed at the detail of these skulls using luminescent PLA.

makerworld.com/en/models/70...

#BambuLab #X1C #MicroCenter
November 12, 2024 at 4:52 AM